久久久久成人精品国产亚洲综合无码av|九九国产精品视频久久|国产精品亚洲二区无码|亚洲va中文字幕无码不卡一区

Thin ceramic slagging slurry valve

Products > Ceramic valve > Thin ceramic slagging slurry valve

Thin ceramic slagging slurry valve

Model: PZ73TC
Nominal diameter: DN50 600mm ~
Pressure range: PN1.0Mpa products
Body Material: carbon steel, stainless steel, etc.
Temperature: ≤150 ℃
Medium: dry dust, water, steam and other media
Connection: Wafer
Contact purchase
shared:

Product Overview
PZ73TC thin ceramic slurry discharge slurry valve for mining, paper, chemical and other types of wear and tear of dry dust, water, steam and other media in the pipeline for opening and closing purposes. Apply to the power plant dry ash system, warehouse pump discharge delivery valve sealing performance, wear resistance, start load, card ash and fouling phenomenon, long service life.

Hand-liquid ceramic slag discharge slurry valve is thin engineering ceramic slagging slurry valve, which is designed for solid-liquid two-phase flow medium pipeline design and manufacture, not only the use of toughened engineering ceramics as off Off and anti-throttling erosion of the main material. At the same time, it is designed with the structure of anti-throttling scouring as the purpose to meet the dual-use function of such medium pipe's cut-off or cut-off + throttling. After years of proven, compared with ordinary slagging slurry valve life has been greatly improved. Hand-liquid ceramic slurry discharge slurry valve for small workplace or installation orientation is not suitable for hand wheel opening and closing valve installation. 


Thin ceramic slag slurry valve Scope of application

1 , mining, steel industry - for coal, filter pulp pulp and so on. 
2 , purification device - for waste water, mud, dirt and clarified water with suspended solids. 
3 , paper industry - for any concentration of pulp, water mixture. 
4 , power plant ash - for the ash slurry. 


Thin Ceramic Slag Slurry Valve Working Principle
Hand Pneumatic Thin Engineering Ceramic Slurry Slurry Valve is used to install the hand wheel opening and closing valve position due to the small working area or the installation orientation. Hand-hydraulic thin ceramic slurry tank valve directly driven by the handle to achieve the valve opening and closing, on-site installation should take into account the operator's ease of operation and standing safety.



PZ73TC thin ceramic slag slurry valve features

1, sealing surface material: structural ceramics or superhard surface alloy materials two. 
2, suitable for cinder, ash and other gas, solid mixed media, gate, valve seat and flow path parts made of structural ceramics, wear resistance, long life. 
3, superior sealing performance, and sealing surface repair. 
4, imported seat can be used for scraping ash board, even in the case of ash off also freely. 
5, the body cavity structure completely avoid the jamming, fouling problem. 
6, drive mode: manual, pneumatic and electric and so on.


The main components of the material

Serial numbernamematerialSerial numbernamematerial
1BodyWCB9Valve stem2Cr13
2SeatEngineering ceramics10BracketWCB
3Valve plate304 + engineering ceramics11Stem nutT
4fillerPTEE12Bearing
5Threaded studs3513HandwheelHt200
6washer1014Bearing gland35
7Nut2515Hand wheel lock nutQ235A
8Packing glandWCB


 

Application specification          

Design and manufactureJB / T 8691
Connector sizeStructure lengthGB / T 15188.2
Flange sizeGB / T 9113.1
Inspection and testingGB / T JB / T8691
materialCarbon steelGB / T12229
SignGB / T12220
AvailabilityGB / 12252

 

Thin Ceramic Slag Slurry Valve construction and installation points
1 , hand-hydraulic thin ceramic slurry valve should be installed before inspection valve cavity and sealing surface and other parts, do not allow dirt or sand adhesion 
2 , the connection parts bolts, requirements Uniform tightening 
3 , check the packing parts require compression, both to ensure that the packing seal, but also to ensure that the gate open flexible; 
4 ,User before installing the valve, the valve must be calibrated model, medium flow connection dimensions and attention to ensure consistency with the requirements of the valve; 
5 , the user at the time of installing the valve, the valve must be set aside space necessary for driving; 
6 , drive means shall wiring Circuit diagram; 
7 , hand-moving thin ceramic slurry valve slurry valve must be regularly maintained, not free to impact and squeeze, so as not to affect the seal. 



Thin Ceramic Slag Slurry Valve Installation and Maintenance Notes
1 , hand wheel, the handle and the transmission are not allowed to lift, and no collision. 
2 , double gate valve should be mounted vertically ( ie stem in a vertical position , the hand wheel at the top ) . 3 , with bypass valve gate valve should be opened before opening the bypass valve ( to balance the pressure difference between import and export and reduce the opening force ) . 4 , with the gear valve, according to the instructions of the product installation instructions. 5 , if the valve is often used switch , lubrication at least once a month.